How do I use ArtResin epoxy resin? A clear guide for beginners

ArtResin, by artists for artists
The story of ArtResin began in 2007, when artists Dave and Rebecca fell in love with epoxy resin - and each other. They loved how a clear, glossy resin surface brought the colors of their paintings to life. However, the user experience and rapid yellowing of products at the time led them to seek a better solution.
Years of research led to a collaboration with a Texas-based chemist. Together, they developed ArtResin epoxy resin, prioritizing ease of use, a clear finish, and reduced yellowing.
Developed by artists, ArtResin brings out the colors and details of your work beneath a beautiful glossy finish. Explore the range and find epoxy resin for your art and craft projects.
ArtResin epoxy resin gives your artwork a clear, glossy finish that brings out the colors and details.
It can be used to coat paintings, photographs, and works made on wooden panels, for example. The keys to success are careful preparation, accurate measuring, and thorough mixing.

ArtResin consists of two parts: resin and hardener. Measure equal amounts by volume and mix for at least three minutes. You have about 45 minutes of working time after combining the materials. A thin coating usually cures to handling strength in about 24 hours and fully cures in about 72 hours.
These instructions apply to ArtResin epoxy resin. Mixing ratios and instructions may vary for other epoxy resins.

What surfaces is ArtResin suitable for?
ArtResin is suitable for coating a wide range of art and craft projects:
- Wooden art panels and wooden objects
- Dry acrylic paintings and fully cured oil paintings
- Photographs and prints
- Paper collages and puzzles
- Stretched canvases
- Ink art and works on Yupo paper
Test compatibility on the same materials before coating your actual piece. Porous paper may absorb the resin and darken. Loose pigments or decorations that are not firmly attached may move when the resin is poured.
If needed, treat the surface with a pre-tested protective product suitable for the material. Let the protective layer dry completely before applying the resin.
Silicone molds can be used for small casting projects because cured resin releases from them. Silicone is therefore not a suitable surface for resin to adhere to. Not all plastics are suitable for permanent coating either.

What supplies are needed to use epoxy resin?


Prepare the supplies before combining the resin and hardener:
- ArtResin resin and its matching hardener (sold together)
- Measuring and mixing containers with a clear volume scale
- Mixing stick and spreading spatula
- Chemical-resistant protective gloves, such as nitrile gloves
- Safety glasses to protect against splashes
- Plastic cover for the work surface
- Support blocks and a spirit level
- Tape to protect the edges of the underside of the project
- Dust cover, such as a sufficiently large box
- Paper towels and a toothpick for removing dust particles
A small blowtorch can be used to remove bubbles, following the manufacturer's instructions, provided the project contains no flammable substances. Do not use a flame with resin containing alcohol inks.
How to use ArtResin epoxy, step by step
1. Prepare the workspace and the item to be coated
Choose a well-ventilated and as dust-free a space as possible. Protect the table and keep all supplies within reach.
Wear protective gloves and avoid skin contact with liquid resin and hardener. Follow the protection instructions on the packaging and in the safety data sheet.
The manufacturer's recommendation is a temperature of about 23–25 °C:. Make sure the resin and hardener are also at room temperature. Keep the temperature steady, especially during the first 24 hours.
The surface to be coated must be clean and completely dry. Raise the project on supports and use a spirit level to check that it is level. Self-leveling resin will flow toward the lower edge on a sloped surface.
Support the canvas from underneath if necessary to prevent it from sagging under the weight of the resin. For large projects, a rigid art panel makes it easier to achieve an even surface.
2. Measure the resin and hardener accurately
ArtResin's mixing ratio is 1:1 by volume.
For example:
- 100 ml of resin
- 100 ml of hardener
- About 200 ml of mixed resin in total
Do not use the same ratio by weight, as resin and hardener do not weigh the same per unit of volume.
Do not add extra hardener to speed up curing. The correct mixing ratio is essential for the resin to cure as intended.
Estimate the amount you need before starting with the ArtResin coverage calculator. Also account for coating the edges and any material lost to drips.
3. Mix for at least three minutes
Mix thoroughly for at least three full minutes. Scrape the bottom and sides of the container as you mix, so all the resin and hardener are combined evenly. A timer helps ensure you mix for long enough.
Air bubbles that form during mixing are not a reason to shorten the mixing time. Resin that is not mixed thoroughly may remain sticky.
Working time is about 45 minutes from the time the ingredients are combined. Heat shortens working time, so prepare your work area so you can spread the mixture immediately after mixing.
Do not leave a large mixed batch standing in a deep container, where it can heat up quickly.
4. Pour and spread an even layer
Pour the mixture over the work and guide it toward the edges with a spreader. ArtResin is self-leveling, but a spreader helps cover the entire surface.
You can let the resin flow over the edges and smooth them with a disposable brush. If you want to make drips easier to remove, tape the underside edges of the work before pouring.
A typical coating layer is about 3 mm thick. Apply thicker coatings in several thin layers. ArtResin's coating instructions should not be applied as-is to deep, single-pour castings.
5. Remove bubbles and inspect the surface
Inspect the surface in good light from different angles. Remove any hairs and dust particles with a toothpick.
The manufacturer recommends using a gas torch to remove bubbles for suitable projects. Move the flame quickly over the surface according to the manufacturer's instructions, and do not heat one spot for long. Keep flammable materials away from the work area.
Do not use a flame over wet alcohol ink or resin tinted with alcohol ink. Alcohol-based additives change the flammability of the mixture. Always follow the instructions for both the resin and the colorant.
6. Protect the work and let it cure
Cover the work with a dust cover without letting it touch the surface. Leave the work level in a quiet place.
| Work step | Approximate time |
|---|---|
| Pot life of the mixture | About 45 minutes |
| Surface hard enough to handle | About 24 hours |
| Thin coating fully cured | About 72 hours |
Cure times depend on temperature and layer thickness. Resin that feels hard on the surface may not be fully cured yet.
Thick and multi-layered projects may need more time to cure. For items such as jewelry and tabletops, the manufacturer recommends allowing an additional 3–6 days to cure after the first 24 hours before putting them under strain.
7. Clean your tools
Wipe reusable tools with a paper towel before the resin cures. Keep your protective gloves on during cleanup.
If resin gets on your skin, wash it off promptly with soap and water. Do not use alcohol, acetone, or other solvents to clean your skin.
Do not pour liquid resin or hardener down the drain. Follow the safety data sheet and local waste disposal guidelines when handling leftovers.
Can ArtResin epoxy resin be colored?
Yes. ArtResin can be tinted with suitable colorants. First mix the resin and hardener thoroughly, then add the colorant.
According to the manufacturer, the amount of colorant can be no more than 6% of the combined volume of the resin and hardener. For example, for a 100 ml: resin mixture, this means no more than 6 ml of colorant.
This is an upper limit, not a target amount. Start with a small amount and also follow the colorant’s own dosage instructions.
Consider the colorant’s effect on the mixture:
- Acrylic paint can change the gloss and shorten the working time.
- Too much colorant can interfere with curing.
Not all inks and paints are suitable for coloring epoxy resin. Check that the products are compatible and do a small test before a larger pour.
Can you add another layer over a cured surface?
Yes. A straightforward approach for beginners is to let the first layer cure, lightly sand the entire surface, and remove the sanding dust. Make sure the surface is clean and dry before pouring another layer. Use appropriate dust protection when sanding.
Sanding makes the surface cloudy, but a new layer of resin restores its clear appearance. It can also fix minor surface imperfections, such as a dust particle left on the cured surface.
The manufacturer also recommends layering over a gel-like, still-tacky surface. Since timing depends on conditions, check the current product instructions for this step. Sanding a cured surface is an easier-to-manage option for your first project.

Frequently asked questions about using ArtResin
Why does epoxy resin remain sticky?
Common causes include an inaccurate mixing ratio, mixing for too short a time, and unmixed material left at the bottom or sides of the container. Too much colorant or a workspace that is too cool can also cause problems.
First check the measurements, mixing, and temperature. Don’t try to fix the surface by adding hardener alone.
How much ArtResin do I need?
The amount depends on the surface area, layer thickness, and edge treatment. Use the manufacturer’s coverage calculator and check whether the stated amount refers to the ready-to-use resin and hardener mixture.
For example, 200 ml of ready-to-use mixture contains 100 ml of resin and 100 ml of hardener.
Can you coat alcohol ink artwork with ArtResin?
Artwork made with alcohol inks can be coated once material compatibility has been confirmed and the piece is completely dry. Test first, especially when using multiple inks or protective treatments.
Coating a dry ink piece and mixing liquid alcohol ink into resin are different techniques. Do not use a flame with wet alcohol ink.
Does ArtResin prevent yellowing completely?
ArtResin contains UV and HALS light stabilizers to reduce yellowing. This does not guarantee that the surface will never change.
The lightfastness of the artwork’s own colors also affects how well the finished piece holds up.
How long does ArtResin last?
According to the manufacturer’s PDF guide, the recommended shelf life is about one year unopened and about six months after opening.
Check the information on your own packaging and keep containers tightly closed according to the manufacturer’s instructions.
Start with a small resin project
A small, sturdy art panel is a good first project. Once you’re familiar with measuring, mixing, and applying, you can try larger surfaces and different color combinations.
Explore ArtResin epoxy resin in the Frenchic online store and plan your first resin project.

